Take a look at our trusted solutions! A two-bedroom home was in need of a repair for their worn-out, year-old, lateral field in poor soil and cracked fiberglass septic tank. October 12, , Zoeller buried a Time Capsule to celebrate and commemorate 80 years of Zoeller history! The time capsule ceremony was originally scheduled to take place in early to mark the end of Zoeller's 80th Anniversary celebrations.
Water Movement Made Easy We manufacture a wide selection of residential and commercial pumps and accessories to provide the best solutions for moving wastewater and effluent.
Learn More No Thanks. Zoeller pumps are made of cast iron, stainless steel parts, and a clog resistant pump intake so they are easy to install highly reliable so you are unlikely to experience sump failure! Zoeller sump pump models can be installed by placing them at the bottom of the pit, attaching the sump pump switch and drain lines. You can install your own sump pump in about 30 minutes or you can call our team of sump pump installation experts at The weep hole on a Zoeller pump should be installed a few inches above the water line to avoid sump pump burnout.
Save my name, email, and website in this browser for the next time I comment. Best Sump Pumps. Best Pump Alarms. How to Install a Zoeller Sump Pump. Information » How to Install a Zoeller Sump Pump If you bought a Zoeller sump pump and are not sure how to install the sump pump then you are not alone.
Step by Step Installation Instructions Follow these step by step instructions to install your sump pump and check valve in your basement. Frequently Asked Questions How do you install a Zoeller sump pump? Can I install my own sump pump? Put the old sewage pump in a bucket to control the possible waste accumulation and prevent it from dripping onto your property. Check the pipe, connectors and basin: Inspect these accessories to find out if you can reuse them in your new system.
You may need to replace them if they have cracks or stubborn stains. How to Install the New Sewage Pump Now that the old unit is out of the way, you can follow these helpful sewage pump installation tips: Clean debris out of the basin: If you took out an old sewage pump, look into the pit for damage and other abnormalities. Carefully get rid of any materials or waste that may have accumulated on the basin walls.
Use a scraping tool to take off the old seal so the new one will be strong and prevent gas leaks and odors. Position the basin: To prevent potential leaks, secure the container with hard hold glue before attaching the pump. Ensure the unit is stable so it doesn't tip or fall when water hits against it. Since this basin operates by gravity, you need to position it lower than the ground so the wastewater can flow into the tank.
Install the new check valve: Set up the new check valve before putting the pump in the sewage basin. You may want to position it so the water can pass upward into the main sewer line. To glue this component to the pump, apply primer inside the fitting and outside the discharge pipe. Slide the coupling on top of the pipe, then attach the fitting to the discharge pipe with PVC cement.
Twist it slightly and hold for a few seconds to secure the bond. Set up the float switch: Install the float switch on top of the pump and secure it with heavy-duty glue. Position it so the trigger is pointing at the basin and has a free range of motion. Open the vent outlet enough to release as much water as possible each time this component activates the sewage pump.
Adjust the float so the tank's wastewater level doesn't get too low below the drain inlet. Test the pump and float switch: Connect the new pump to a dedicated circuit and test it by activating the float switch and making sure it turns on the system. Only allow the pump to run long enough to hear it working, or else it could become damaged. Make sure you've installed the float switch at the right height so the system can operate properly. Measure and cut the PVC pipe: If you need to install a brand-new discharge pipe, measure the old one and consider the proper dimensions given the new check valve's installation.
Use a hacksaw to cut it on a raised surface, and smooth out the edges with a deburring tool. Drill a weep hole: A weep hole prevents the pump from drying out due to air locking in the pipe. It also controls the flow of water and air away from the pit, allowing the system to flow freely every time it needs to empty the basin. You may want to lean the pump at an angle and measure a few inches above the adapter. Drill a three-sixteenths-inch gap into the piping for the best results.
Connect the adapter and pump to the discharge pipe: With primer and PVC cement, secure the male-threaded adapter to one side of the PVC pipe. Thread the side of the pipe attached to the adapter into the sewage pump, tightening it with a wrench.
Be careful not to overtighten it so you don't crack the fittings. Lower sewage pump into the pit: After you've cut the discharge pipe and attached it to the sewage pump, bring both components into the basin.
Position the float switch so it's away from the wastewater inlet. It may help to install the discharge pipe to block the inlet water from covering the pump directly. When you've confirmed every piece is in the right position, secure the electrical wiring with zip ties to prevent snagging. Slide the adapter from the check valve over the coupling before securing it to the discharge pipe.
Connect the coupler with glue to the discharge pipe and attach it to the check valve. Slide the adapter up and tighten the check valve with your hands. Overtightening the system may crack the fittings, so avoid this. Test the sewage system: After you've securely placed the pump inside the basin, make sure the float switch can move freely within it.
0コメント